It’s time to update this post after answering hundreds of comments from readers and helping them with their jet ski starting problems.
I’ve added more things to try when your jet ski is refusing to start, along with many new tips. It can be frustrating when your jet ski won’t start, but with this new updated guide, it will help you figure out why.
Why Your Jet Ski Won’t Start
A jet ski not starting is most often a dead or weak battery. A bad starter relay can also be another reason for a jet ski not starting.
Usually, when you hear multiple clicks from your jet ski, it’s a bad battery and if it’s one click it’s a bad starter relay.
A bad battery and starter relay are the most common reasons for a jet ski to not start, but here is a list of other things that can cause starting problems that we’ll go over in this post.
- Bad or weak battery.
- Bad starter relay.
- Bad spark plugs.
- Bad or wrong key or Locked.
- Sucked something up.
- Bad starter button.
- Bad fuel injectors.
- Blown fuses.
- Bad ground connections.
- Bad gas.
- Bad fuel lines if it’s a 2-stroke.
- Bad starter motor.
- Bad fuel pump.
- Broken safety lanyard or not attached.
- Fuel selector is not on, 2-strokes only.
- TOPS switch is bad.
- ECU or ECM is bad.
- Overheating/cooling issues.
- Throttle position sensor bad.
- Blown engine.
- Damaged gauge.
1. Bad Or Weak Battery Can Keep A Jet Ski From Starting
The most common reason for a jet ski to not start is a bad or weak battery.
You can tell it’s a bad battery if you press the start button and all you get is multiple clicks coming from the engine compartment. That multiple clicks are the starter relay clicking because the battery doesn’t have enough power to turn the engine over.
If you put the key on and the gauges do not come on, it is another clue that the battery is dead. A completely dead jet ski battery won’t have enough power to turn on the display or make any noises.
Even if the battery seems fine or is brand new, it still can be a bad battery.
The only way to test if a battery is good is to use a load tester. Testing the voltage doesn’t mean anything, you need to test the amps, and only a load tester can do that. You can take the battery to any autoparts store and have them load test it, or buy a load tester* to keep in your home.
The best jet ski battery and the correct size to get can be found in our “The Best Jet Ski Battery + What Size You Need” post.
A battery being bad at the start of the season is quite common. Batteries go flat if they’re not used for months, so it’s important you keep a battery charger on your jet ski battery in the off-season. The best battery charger and other questions relating to your jet ski batteries is covered in this post.
2. A Bad Starter Relay
The next most common reason why a jet ski won’t start is that the starter relay(solenoid) is bad.
You can tell the starter relay is bad if you only get one click or thud from the engine compartment when you press the start button. The gauges will come on when you try to start, but all you get from the jet ski is one click, that is a sign of a bad starter relay.
The starter relay is a component that takes the lower power coming from the start button and has it control a high-power wire coming from the battery. The high-power side goes directly to the starter motor to turn the engine over.
It’s not uncommon that you need to replace your starter relay for your jet ski at least 2 to 3 times within its lifetime. You can’t predict when your jet ski’s starter solenoid will fail, it’s random, but it will always give a solid thud when it does fail.
Starter relays are not hard to replace for most jet skis, it’s often two mounting bolts, plus two terminal nuts and disconnecting the low power side wires. It can be dangerous replacing the starter relay, so be sure to disconnect the battery fully before doing anything.
3. Bad Spark Plugs
If the jet ski engine turns over but refuses to fire up or sputters a bit, then that is often a sign of bad spark plugs.
The jet ski may even fire up, but won’t stay running or runs very rough.
Ideally, you should change the spark plugs in your jet ski every year, at the start of the season is the best time. Here is a list of maintenance items you need to do for your jet ski.
4. Bad key, wrong key or Locked
Customers putting on the wrong key is more common than people realize.
It’s not uncommon for a jet ski owner to get two jet skis and the keys not be programmed alike. The keys look the same, but if you have a Sea-Doo and put the wrong key on the jet ski, it won’t start as each key is programmed to each machine. If you own multiple Sea-Doo’s ask your dealership about getting all your keys programmed alike to keep this from happening.
If it’s the right key, there is a chance the key or post could be bad. While rare, I’ve seen a few number of Sea-Doo keys go bad and the only fix is to get a new key. The post where the key plugs into can go bad too, one way to test that is to put a strong magnet up to it and if the Sea-Doo doesn’t beep the wrong key sound then the post is mostly likely bad.
Yamaha waverunners have some models that have key fobs, and you can lock the jet ski like you do your car. If your Yamaha has the key fob or a PIN code access, make sure it’s unlocked before trying to start it.
Kawasaki has keys similar to Sea-Doo that go in the glove box, so make sure they’re inserted before attempting to start.
5. Sucked Something Up Into Jet Ski Pump
It’s a good idea to check your jet pump for anything inside it like ropes, rocks, sticks or any large item that’s not supposed to be there.
Jet skis are direct drive, this means the jet pump is connected to the engine, there is no transmission. So when you go to start the jet ski, the jet pump will also spin and if something is stuck in the pump, it will keep the engine from starting.
One of the first things you should check when you get the jet ski out of the water for a non-starting problem is the pump. Look from the rear and also safely crawl under the jet ski to look into the pump to make sure nothing is blocking the pump blades from moving.
If you need to remove something from the pump, I have a post here to show you how.
6. Bad Starter Button
A bad starter button can keep a jet ski from starting and was a common problem for 2-stroke jet skis.
The rubber of the start button can wear out and cause it to not work. The plastic start buttons didn’t give much trouble, but the rubber ones do wear out quicker.
If the button is torn, you have to press really hard with your nail, or the button is super faded, then replacing the start button is a good idea.
Do note, the start button of a jet ski is not the same as your car. You must hold the start button down on your jet ski until it’s fully started. Pressing the start button once on a jet ski will not start it, it needs to be held down until the engine gets going.
7. Bad Gas
If the jet ski turns over but won’t fire up or runs rough, and you replaced the spark plugs, then it’s most likely bad gas.
Gas goes bad when you let it sit without adding fuel stabilizer to it. It’s getting even worse with more ethanol is added to gas.
If your jet ski has been sitting for a while, then it’s a good chance the gas is bad and keeping your jet ski from firing up. Safely remove the old gas and add fresh premium gas to your jet ski.
This is why I like to store my jet ski near empty (1 or 2 bars of gas) in the off-season and when the season starts I fill it up with fresh 93 octane gas. Along with new spark plugs, you’ll be starting the season off right.
8. Blown Fuses And Relays
If you get nothing out of your jet ski when you put the key on or press the start button once, then it could be fuses or relays located in the fuse boxes that have gone bad.
Locate the fuse box, often near the battery, and check every fuse. If a fuse is blown you need to replace it.
Don’t forget to check the fuses that may not be in the fuse box, there are often fuses inline coming out the fuse box or near the battery wrapped in a rubber sleeve.
It’s not uncommon for me to see a jet ski blow a fuse because someone hooked the battery up backwards. Other times fuses blow just because, there is no good reason except the fuse was not good. If a fuse keeps blowing, you need to figure out what is blowing it.
There are also small relays, look like a small black box with multiple terminals, that go into the fuse box area. These smaller relays are used to power on the low-power items and get the jet ski into turning on mode. There is no good way to test these relays unless you have an ohm meter, but if you’ve gotten to the point of testing them, it’s just easier to replace them. These little relays are less likely to fail than the main starter relay, but they can fail.
9. Bad Ground Connections
If a jet ski is older, corroded ground connections are quite a common problem for starting issues and many other problems.
If you have corrosion around the battery terminal cables, then it’s mostly likely your problem. Corroding battery cables also mean the ground wires that connect to the engine block are corroding too.
You will need to clean all the ground connections, including where they connect to the engine block.
10. Bad Starter Motor
A starter motor going bad is more likely on 2-stroke jet skis than 4-stroke, but it can happen to both.
One way to tell it’s the starter motor that is bad is if all this below is true.
- Battery is good.
- Starter relay is good.
- Nothing is in the pump.
- Engine is not hydrolocked.
If the above is true, then it’s most likely a bad starter motor.
If you have a 12-volt test light probe*, you can see if the starter motor is getting power to it. Clamp the negative to the battery or ground and put the probe light on the positive connection of the starter and press the start button. If the probe light turns on when you press start, then you’re getting power to the starter, and the next thing you need to do is remove the starter and bench test it. If you get no light from the probe, then the problem is before the starter.
To bench test a starter motor, you have to remove it from the engine and put it in a bench vice clamp and hook it directly to a battery. Starter motors are very jumpy, so you need to make sure it’s secured tight in the vice clamp before connecting it to a battery.
11. Carburetor Issues Or Bad Fuel Lines (2-Strokes Only)
If you have a 2-stroke jet ski that has a carburetor, then a super common starting problem is a clogged carburetor or old fuel lines.
If you have a 4-stroke jet ski, then this section is not for you, as all 4-stroke jet skis are fuel injected. You’ll know you’ll have a carbureted jet ski engine if you have a choke cable.
If you don’t know if you have a 2-stroke or 4-stroke, then check out this post.
With the rise of ethanol in gas, it’s been doing a number on 2-strokes carburetors and fuel lines.
The solution is to clean the carburetors and replace the fuel lines, and then avoid ethanol gas as much as you can.
12. Bad Fuel Injectors
Not super common, but bad fuel injectors can keep a jet ski from starting or give you running issues.
Bad fuel injectors can also cause “ghost” problems when it comes to starting. If the jet ski will start but not start again after sitting or is rough to get going, it could be the fuel injectors.
I’ve had a jet ski that would start but if you let it sit for a bit it would refuse to start back up. One of the fuel injectors was leaking and dumping gas in, causing the engine to be flooded and refuse to get running.
Messing with fuel injectors is a dangerous repair and should only be done at the dealership.
13. Hydrolocked Jet Ski Engine
A jet ski that is hydrolocked means there is water in the engine, which is not a good thing.
You can get water in the jet ski engine from it sinking, drain plugs left in and flooded by rain water, broken cooling components and more.
A hydrolocked jet ski engine will refuse to start, and trying to start a hydrolocked jet ski can bend piston rods and do further damage. If you flipped your jet ski, follow these steps.
An easy way to test if there is water in your engine is to take the dipstick out and see the color and consistency of the oil. If the oil is runny and looks like chocolate milk, then that is bad. You want the oil to look amber or black and should not be runny.
Another way to see if water is in the engine is to remove the spark plugs and turn the engine over. If you get a geyser of water shooting out the spark plug holes, then there is water in the engine.
Hydrolocked engine is best fixed at the dealership or repair shop, especially if it’s a 4-stroke jet ski. You’re going to need several oil changes and the intake taken off to get all the water out.
14. Bad Fuel Pump
A fuel pump that is bad can keep a jet ski from starting, but fuel pumps going bad are not common and more of a fluke failure.
If the jet ski turns over, you’re getting spark, but the jet ski does not prime or no gas is coming out the fuel injectors it’s mostly a bad fuel pump.
Another way to tell it’s a bad fuel pump is if the gas gauge is not working, as that is a part of the fuel pump.
The fuel pump is located in the gas tank and is a dangerous repair and should only be done at the dealership.
15. Broken Safety Lanyard Or Not Attached
All jet skis have a kill switch called a safety lanyard that attaches to you and the jet ski. So if you fall off the jet ski, the engine will shut off.
Sea-Doo’s safety lanyard is the key, while Yamaha and Kawasaki have dedicated lanyards on the handlebars that wrap around your wrist.
You need to make sure the lanyard is attached to you and connected to the switch on your jet ski, or else it won’t start.
The switches for the safety lanyard can fail, especially if water gets near the contacts.
It’s recommended you let the dealership repair these lanyard switches, as it’s meant to save lives and needs to be done properly. Make sure your waverunner doesn’t have a recall on the kill switches either.
Tip: If your safety lanyard cable is stretched, damage, or broke, you have to replace it. They do not sell the cable/string separately, so you must replace the whole thing, which means for Sea-Doo you need to get a new key.
16. Fuel Selector Is Not On Or Broken (2-Strokes Only)
If you have a 2-stroke with a carburetor, you’ll most likely have a fuel selector.
The fuel selector can be moved to off, which shuts off all gas to the engine and can keep it from starting.
Make sure the fuel selector is in the “ON” or “Reserve” position when trying to start your jet ski.
An interesting way to know if your fuel lines are going bad is if the jet ski runs fine in reserve but not while in the “ON” position. People don’t use the reserve much, so the lines don’t wear out as quickly.
17. T.O.P.S Switch Triggered
The T.O.P.S Switch (Tip Over Protection Switch) is a switch that is used to determine if your jet ski is upside-down. If the switch thinks you’re upside down it shuts the engine off. If you do flip a jet ski, do this.
The T.O.P.S Switch is used to protect your engine if you flip it and to protect you from the spinning impeller blades.
The old T.O.P.S Switches were simple mercury switches, and they could get confused about what’s up and wants down. The newer T.O.P.S Switches are more reliable, but can still fail.
If you feel like you’ve tried everything else, this is a good one to try. The only good way to tell if a T.O.P.S Switch is bad is to hook it up to the diagnostic computer, as it will throw a fault code.
A bad T.O.P.S Switch will keep a jet ski from starting, and it’s one of those things you’ll try last because it’s not common for it to fail, especially for newer jet skis.
18. ECU or ECM Is Bad
A bad or damaged ECU or ECM can keep a jet ski from starting.
The ECU (Engine Control Unit) and ECM (Engine Control Module) are the “brains” of your jet ski.
If you tried everything else and the jet ski won’t start or won’t run right, then the last thing to check is the ECU or ECM.
Unless you got the proper testing equipment from the manufacturer, it’s hard to know if the ECU or ECM are bad. Most dealerships don’t even get the testers out and just replace it with a known good computer to see if they’re bad or not.
ECU and ECM’s each cost about $1,000 to replace and will require a dealership to program them to your jet ski.
19. Overheating And Cooling Problems
If a jet ski overheats for too long, the computer will kill the engine to protect itself.
An overheated engine can refuse to start until it’s cooled back down.
If the jet ski is refusing to start back up after riding, you may have overheating problems. If you do have overheating problems, alarms should be going off to warn you.
Make sure you don’t run your jet ski out of the water for no more than 15 seconds.
Sea-Doo uses a closed loop cooling system, while Yamaha and Kawasaki use open loop. Open loop can get clogged with debris and cause the engine to overheat, but your jet ski should be beeping at you with warning lights.
20. Throttle Position Sensor Is Bad
Not super common, but a bad throttle position sensor can keep your jet ski from starting.
Fuel injected jet skis, which all 4-stroke are, will have a sensor to determine the throttle positions. If the jet ski throttle is in too much, the jet ski will refuse to start as it’s in drown mode.
Sea-Doo mostly, if you hold the throttle all the way in it goes in a drown mode which kills the fuel injectors. This mode is for testing things like compression and to make sure the engine spins without firing it up.
If the throttle sensor is not set right or confused, this could be why your jet ski won’t start. To reset this, you’ll need to hook the jet ski up to the diagnostics computer to reset the TPS.
Also, make sure you’re not touching the throttle when trying to start your jet ski. I know a few dirt bike and motorcycle guys that are in the habit to give a little gas to start them, but this is not something you do for a jet ski.
21. Blown Engine
A blown jet ski engine can refuse to start or not run well.
You can tell if a jet ski engine is blown by checking its compression with a compression gauge. You want the PSI to be over 100PSI and each cylinder to be within 15% of each other.
An engine that was hydrolocked and not taken care of properly can also blow the engine.
Running improper fuel and air mixture can lead the engine to blow too.
Running the engine to where it overheats and damages it can also blow the engine.
There are many things that cause a jet ski engine to blow, but it’s usually something major that happened to lead to such events. While a jet ski engine blowing can cause it to not start or run right, it’s not always the case and is one of the more rare reasons.
22. Damaged Gauges
A damage gauge could keep the jet ski from starting or confuse you into thinking the battery is bad. A damage gauge could keep from lighting up and ringing the buzzers too.
The main communications you have with your jet ski is the gauge and the buzzer, so if both don’t come on, it could keep you from getting your jet ski started or knowing what’s wrong.
Jet Ski Won’t Start In Water
If your jet ski will start when out of the water but won’t start when in the water, then the most likely problem is the battery or starter motor.
Jet skis are a direct drive system, so if the engine is spinning, so is the impeller. When the jet ski is put in the water, the starter motor and battery need to now work against the water, so if either one is bad or weak the jet ski won’t start.
233 thoughts on “Reasons Why Your Jet Ski Won’t Start”
I have a 2008 gtx 215 that will not start. I have gone through all the “KISS” steps and have 12 vlts all the way to the starter but it doesn’t do anything nor make a sound. I tried to jump across the starter relay but it also was a no go to try get the starter to do anything! I’m at the conclusion that the starter locked up and I hope to replace it. Does my conclusion on what is the problem go along with what you believe is the problem? Your advice is greatly appreciated!!! Thanks for any advice you ❤️ have for me!!
If you got 12v at the starter, then most likely it’s a bad starter motor. It could be hydrolocked if it’s been sunk or water got in the engine, that would keep it from turning over. Also, something stuck in the pump would keep it from moving. But those would give a slight clunk of some kind, dead silence would be a bad stater motor.
god bles you for I have the same problem with mine
Will a damaged supercharger keep a jet ski from starting?
It’s unlikely a super charger will keep a jet ski from starting, but it is possible. The super charger would have to blow and damage the engine to keep a jet ski from starting. That would be a pretty serious situation, I would check the battery first before doing anything else, as the battery going bad is the most common reason for a jet ski to not fire up.
Have 2004 Polaris Virage. Daughter was riding, everything was working great then, ski cut out all of a sudden on her. She immediately thought it ran out of gas, since it shut off so abruptly. Got gas, went to start it & the battery was drained, wouldnt even try to turn over. Got a jump, started up & rode it maybe 200 yard’s & shut off on her again. Have pulled battery, to charge & might get a new battery but, did clean terminal’s & check connection’s, all were tight & cleaned. Going to check fuse’s too, anything else I should check while in there?
I would check to see if the battery is charging or maintains a charge. Turn the engine on and using a volt meter check the voltage, if it’s not between 13.5V to 15V, then you have a stator or rectifier problem. https://www.steveninsales.com/do-jet-skis-have-alternators-jet-ski-charging-system/
I have a 2001 Yamaha GP 1200r I purchased last summer. Running hours are around 140. It runs like a bat out of hell. It sat all winter covered. When it sits for about 3 days it’s hard starting. So I went to it ready for this summer. Put a new battery in it turns over but won’t fire. I checked plugs, fule filter and all things necessary. Bleave me I have read all of the threads on this modle. After checking out everything. I frickin light came on in my brain. One of the simplest things. I un screwed the gas cap. It fired right up. So this is one thing that I think has never been mentioned on other threads of this hard starting problem. It vaper lock. This simple trick saved me a lot of money and should be passed down to everyone having this same problem with hard starting. It still runs like a charm. Thanks.
What I thought would be an easy fix is turning into not so easy at all. I’ve got a 15 seadoo spark. It turns over but doesn’t run. I replaced the spark plugs, battery, fuel and a small list of other things. I’m getting spark, pulled the injectors and they are working fine. I got candoo pro and it said the tps was bad. Replaced the tps and cleared the code. Still nothing. I’m getting 11.9v while cranking and 12v under no load. I pulled the injectors and plugs tonight to let them air out in case I flooded it trying to start. It cranks strong but just won’t run, or even sputter. I’m at a loss, the dealer is a month out after I drop it off. I was hoping to run it this summer.
This is a tough one. I would check compression before going forward, then check all the fuses and relays. Take the fuse box out and make sure nothing the fuses plug in to is loose. Make sure the oil is good and not milky, either. The fuel filter located on the fuel pump can get clogged, but if you’re getting fuel at the injectors, then it should be fine. Make sure you’re NOT touching the throttle when starting as doing so puts the Sea-Doo in drown mode which is exactly what you’re experiencing. The throttle lever could be bad, maybe it’s thinking you’re holding it in and that is why it’s not firing up. Worse case, it could be a bad ECU, but check the wires going to it to make sure they’re not loose or broken.
Hey Steven – Jut came across your site, and hoping you can give direction. I have a 2018 Seadoo GTX 300, about 50 hours on it. After launching it successfully this year, I tried to star it and got no lights, beeps or or clicks. I replaced the battery (even though the original was still testing as ok) checked all the fuses, and Jumped starter solenoid with a screwdriver – it sparked but nothing happened. All other connections look solid. When I remove the lanyard, and hit the start/stop switch, nothing happens on the display. Appreciate any guidance you can provide!
With the key off, tap the start button once. If the gauges don’t come alive then the Sea-Doo is not getting any power. I would start by looking at fuses to make sure none are burned out along with the 30 amp relay (should look like this… https://www.ebay.com/p/1851237250) Make sure to disconnect the battery before doing this. If the gauges do come alive it could be a bad key or DESS post.
I have a 2005 seadoo gtx 155. We have been having issues with it starting. We have to push the start button several times before it will finally crank over. We checked the solenoid and it seems ok. We changed the spark plugs too. Rode it this weekend and it did the usual, where we have to push it several times for it to start. Went to pull it out of the water today and it wouldn’t start. It sounded like it wanted to, but it wouldn’t fully crank over. Anyways, took the key off the post and this blowing noise started from the engine. We went to disconnect the battery to make the blowing noise stop, and the connections sparked and the jet ski tried to start on its own, Without the key on the post and without us pushing the start button! Anytime we touched the connections on the battery, the jet ski would make noises like it was trying to fire up and start. Again, the key was disconnected and we werent pushing the start button. So we disconnected the battery and left it at the dock. Any idea? Thanks!
The first part sounds like a bad starter relay, but that second part is a really crazy one. The Sea-Doo won’t start unless the key is on unless the starter relay was jumped, the engine will turn over but not fire. I would start with getting a new starter relay first and then a new battery, even if they look fine, replace them. It almost sounds like the starter relay failed in the closed position or something is jumping the connection or the computer has fried.
I have sea doo wake 155. I replace the battery last year and this year when I put it in, the motor would turn over but not enough to start. I took out battery to charge and once I put battery back in, it cranked right up but after a short drive I turned it off and it didn’t have enough power to start it back. Jump box worked to crank it up but after taking battery out and testing it, it’s showing 13.3 on voltage meter but motor will turn over but not strong enough to crank it. Anyone have any idea?
It sounds like the battery is bad. Never go off the voltage as it can lie, you need to know amps and the only way to do that is with a load tester. You can take the battery to any autoparts store and many of them will load test a battery for free.
Coming out of winterizartion, my Sea Doo 2007 GTX 155 will turn over, but will not run. Battery is fully charged. What do look at first?
I would change the spark plugs first and make sure the ignition coils are on tight. Then I would put fresh gas in it. I have a de-winterizing guide that goes over more here: https://www.steveninsales.com/de-winterize-jet-ski/
I changed spark plugs, still won’t start but now it gets a message PO231. What does this mean?
That’s a fuel pump shorted to ground fault code. What’s interesting to me is that I would get that code when opening new Sea-Doo GTI SE 155’s out of the crate back in 2007, and the only solution was replacing the fuel pump. Something about that batch of fuel pumps went bad when you put the key on when there was no gas in them. Swapping out with a new fuel pump always fixed it. I would check for any blown fuses first just to confirm, and if none are blown, you may need a new fuel pump.
Thank you. Thankfully it was a fuse that was blown. Thanks for the great work you do.
Hi Steven, could you please help?
I have tried to start my yamaha waverunner 700 after winter first time and after one click it wont turn over,and red cable to starter gets really hot. Wot can it be? I have new battery and spark plugs too
It sounds like something is keeping the engine from spinning over, either the pump or engine could be locked up.
I have a 2007 Sea Doo Wake 215 that was just on the water for the first couple of times after storage (garage). I got it to the ramp and rode for about 10 minutes to my home. It ran amazing. Once i started it back up, i got codes P0351, P0352, P0353 & check engine light. I stopped the engine and tried to start it again, but now it wont start. It cranks over for about 1 second then dies and throws the codes. It was just serviced at the end of last season with plugs, filters, oil.
It sounds like the Ignition coils are not tight or all 3 have gone out. Since it was serviced recently, I’m thinking the guy who did it did not fully seat the coils in place.
As an update, I changed the ignition coils, spark plugs, new battery, cleaned off wires and any corrosion with wire brush, replaced some fuses, replaced rectifier… all with no avail. Still kept getting the same codes. The ski only has 27 hours on it… it will start up great when cold and run awesome. U til you turn it off and try to start back up.. it will start throwing the codes once you do. Ended up taking it to a local shop and they did the water test, got it to throw the codes, took it back and replaced the ski ECU with a known good ECU, and the codes supposedly went away. Now I’m waiting on my new ECU to come in. Hoping this is the final fix. I’m >$2K in on this thing. Extremely frustrating! Hope this helps others out! Start with the simple things first. Corrosion, battery voltage, fuses, spark plugs, rectifier, coils. Probably in that order. If that’s not it, check your wiring harness… it may be that or a bad ECU. Apparently these things tend to go out quite frequently. :/
I have a 2015 Seadoo GTX 260
Ran it out of fuel now when i try to start it, it turns over a couple of times then comes up with “Limp home mode” and wont start.
Any ideas? Cheers
It could be anything, but you need to get it to a dealership so they can read the code that is causing the limp home mode.
Hi have a 2009 rxt 255. Was running fine, topped oil up then nex day was running ok, for about an hour. Turned off to get kids on and would not start. All lights and noises normal.
Checked dipstick and oil levels are overfilled. Advice please on what to do.
It seems you may have put too much oil in it. There is no need to top up the oil on a 4-stroke, you change it when you do a service. It was the old 2-strokes that needed the oil top up and added from time to time. If your 4-stroke is low on oil then something is leaking the oil or it’s burning the oil which is not good.
I have 2021 FX HO. The first 45 hours the ski has started fine. It has been serviced at 10, 38 and 53 hours.
Since 45 hours I have had this intermittent start issue, now 6 times. The issue is a single click. I have now noticed a pattern on when this occurs.
For the most part it occurs after sustained period of hard riding. But it may start between 5-10 and 15-20 times without issue before the single click on the rsix times it has now happened.
Each time I have taken to the Yamaha dealer, to look at and they never find anything. They put it on the diagnostic system and check everything. I replaced the battery, even bought a new relay Solenoid, but they said the old one was fine. Every time they load test the battery check terminals etc, etc. Battery is not the issue or connections are not the issue.
In 3 of the times I have had the issue, after being towed back to the boat ramp, it starts on the trailer or when I get home and can luckily flush out as most riding is in salt water, although the issue has happened twice at the lake.
I am about to take into the dealership for the 6th time. I have read multiple threads. The only thing I can now think of is that the issue is some deep embedded fault in the ECU or other electronics. The ski is still under warranty and only 9 months old.
The problem I have is very frustrating as I can’t go on rides with confidence given the ski might not start.
I have a 2018 FX SVHO which has never had a starting issue. I look after my skis and service more than regularly.
I am inclined to say to Yamaha to take it back and replace as it’s a dud.
Any further thoughts on wh
This is a tough one. The only thing I would add is to try is a different dealer just to get a new set of fresh eyes on it. I would also consider looking at the safety lanyard too as I know some 2021 Yamaha’s had some kind of issue with water getting in them and corroding connections.
hey – so i have a 2017 GTI SE. it often won’t start. no clicks. nothing. if i remove the battery and put it back in, this typically fixes the problem and it starts right up. usually can start and stop it fine after that until it sits again for a week or two.
battery is for sure fine. i swapped it with one in our other GTI, which always starts fine and the problem stuck with the jet ski.
also replaced the starter relay fuse – big black fuse inside the fusebox. no change. and i checked all the other fuses and cleaned them. all seem fine…..
seems like it must be a short in the wiring perhaps? do i just start checking continuity and replacing wiring…?
thx in advance for any thoughts….
If you’re chasing something like this you need to see what fault codes the Sea-Doo is throwing before going forward as this is quite strange. Only a dealership or repair shop can read these codes. I’m wondering if it’s an ECM problem as that is super odd.
Excellent guides and comment. Have a Yamaha FXSHO 2008, with very few hours, but suddenly one click and starter did not turn over. Multiple (up to 10), start button presses and the pwc started. Battery new, so not problem. I have the 700p service manual, so did the test on incomming current (from Battery) to the solenoid 12,6V ( grey taped) = OK. Then tested the old solenoid according to the servicemanual, by taking it out (Found a very good guide how to take out the solenoid (see below’)). NOTE test indicted the solenoid was OK! But I read this article and felt convinced so went and swapped to a new one in spite of the old one apparently working… Now All working perfect with new solenoid!! Lesson learned not allways trust manual… disasembly video below.
I have a 2006 Sea Doo RTX 4-tec super charged. it has been a great machine. recently we have had a problem with starting. after 1 use in the water we will tie it to a buoy and it may sit for an hour, we will try starting it to ride again. we place the fob on the starter and it chirps as normal. it cranks over just fine but will not fire. we have replaced the battery twice and this did not help.
we will take it out of the water and let it sit overnight. the next day it will start just fine. we will ride it once for any length of time but when we turn it off and don’t ride for an hour and go try it again, it will crank over just fine but will not start.
I had a similar Sea-Doo give me the exact same problem before and it turned out to be a bad fuel injector. The fuel injector would leak slowly and flood the engine and keep it from cracking.
Hi Steven I just obtained an 02 seadoo gtile. Got brand new battery but it just turns over one time really weak then clicks repeatedly will turn over again really weak then foloweed by the clicking again and so forth I have jumped relay same exact thing happens any thoughts? Thanks again for any help
Either the battery is weak or something is keeping the engine from spinning. Something in the pump or a jet ski that old some parts could be corroded shut. A start motor being bad is not out of the question either.
I have a 2010 Sea Doo GTI 130 it will start but it revs extremely high and it won’t go forward or back was thinking something could be stuck in it but not sure. Any ideas?
It sounds like a stripped driveshaft. It’s rare for a 130HP engine but was a problem around that time.
I have a 2016 Sea-Doo GTX and when I put the key on the port I’m not getting any display and the ski doesn’t start. This happened when out on the water after running just fine. I’ve load tested the battery and it’s good, changed any fuses that seemed blown and still nothing. Any thoughts?
Make sure you press the start button once to wake the gauges up before putting the key on the Sea-Doo. If you still have the issue then you’ll more than likely need a new key.
Hey Steven…I just stumbled on your site looking to find an answer and super glad I did. There is a ton of information here.
I have a 2007 Honda Aquatrax that I can’t get running. I took it out to “unwinterize” it and it ran great for 10-15 min. I stopped for a minute to rest and it wouldn’t start back up. I put the kill switch on and it beeps twice and the screen flashes and goes off. It will continue to beep twice every couple seconds and the screen flashes on and off, but nothing happens after. The start button does nothing when this happens. The battery is virtually brand new and I checked the charge and it shows fully charged. Any ideas???
You got a bad connection somewhere. Over time the copper wires that connect to the battery corrode and cause these odd events. I would clean the battery terminal wires from the jet ski first to see if that helps. This video can help: https://www.youtube.com/watch?v=R3HPbTsK3BE
Hi i have a wave runner and when i push the start button it clicks and then when i let go of the button it clicks. The lights and the gauges on the dash screen doesn’t come on. I got the battery tested twice and both times they said the battery is good. What do you think the problem could be?
One-click would mean the starter relay is bad. As for the gauges, it could be many things. If the jet ski is old enough it could be a bad gauge or as simple as the battery connections are dirty and have corrosion. It could also be a blown fuse.
Had the same thing happen to my seadoo, changed the solenoid, battery and still the same thing. Turned out it was a bad connection in the fuze box. Try pulling them one a a time and see if any rust or dirt is causing the bad connection. Oh and also use wd40 to help waterproof the fuze box.
I have a 2010 Yamaha fx ho which I fish off of.
I always charge the battery when not in use and it fires up first go all the time.
My issue is when I’m out fishing, stop at one spot then move to a new spot, shut the ski off, fish for a bit, then when I go to start it, the ski just won’t fire up- it sometimes takes 4-5 goes before it will actually kick over.
I’ve been told that this could moisture in the exhaust from stopping and starting.
Is this a thing ?
Does anyone know how to stop this from happening ?
If you’re pressing the start button multiple times before it starts then it might be a bad starter relay. I would start with the starter relay before doing anything else.
I have two 2012 gtx 155, one of them coming out of weatherization started fine, but when we went to the lake it wouldn’t start. The display doesn’t come on, and all I hear is one click. The fuses are good, and I believe the battery is ok. Any ideas on what it might be. Any help would be appreciated.
I would start with replacing the battery especially if you did not keep it on charge over the storage period.
So I replaced the starter solenoid, and used the battery out of the other ski that starts fine. Still nothing. And when I bypass the solenoid with a screw driver it cranks over. I even used the key on the good ski, no problems. Just not sure. Any other idea’s?
Sounds like the low voltage side of the starter relay is bad. I would check the fuses and if that doesn’t work you have something else going on and will need to take it to a repair shop to read the fault codes.
Steve Thanks for the website it’s a great resource. I have a 2003 Seadoo Bombardier GTI, starts up and runs great for about a 45 minutes, then begins to stall. Typically gives a hard time restarting, but will restart and run for a few minutes before stalling again. Allows me to get it back to the dock and hoist it out of the water to flush it out and runs fine while flushing. Usually drop it back in the next day and same process happens again. Any suggestions?
Start with spark plugs and then look into replacing the fuel lines and fuel selector. If it’s been sitting for a while the carb might need to be cleaned too.
Hello Steven, I sure do appreciate all of your shared knowledge. I have a 2002 SEADOO GTI LE (2 stroke of course) started up and worked great for a few hours, then on one trip the driver told me he hit a big wave and the unit just shut off, almost like the key was pulled off, now the seadoo won’t start… We get two beeps on plugging in the key, the starter turns over the engine, like its trying to start, but never does. Checked the plugs and there is spark, lots of gas and oil in the unit… It seems so strange that it just quit, almost sounds electrical in nature but i’m baffled by it. Any thoughts?
Try a new battery or maybe something is stuck in the pump keeping the engine from spinning. It’s also 18 years old so I would not be shocked if the starter motor has gone out. Those are the only thing that sticks out to me for that model.
I’m vacationing in the Florida Keys with our twin 2020 GTX Limited. We have been using them without issue but left them in the water well secured this week. No bouncing around or hitting anything, but did have heavy wind. We went to use them today and both are not starting. Key registers, dash comes on, but continuously turns over. Any ideas how we can troubleshoot? We already had the batteries replaced about 6 months ago, and both are well charged.
This doesn’t sound like a battery or starter relay issue as it turns over. It sounds like a spark plug or ignition problem. It could also be a bad gas problem too.
HI Steven, our 2001 Sea Doo GTI stopped running last week. First time we had it out this year. My son thought it was a Low Oil Pressure Shutoff to protect the engine. Cannot find anything listed saying this is a feature. I did fill the oil & the engine turns over great, but will not fire. If the Starter relay was bad, would the engine turn over? Any other helpful hints to check?
If the engine turns over the starter relay is fine. Since it’s a 2-stroke I would start by replacing the spark plugs first.
I have a 2007 and 2008 Seadoo GTI 155. Both have similar hours right around 70. So after storing them for winter this year we were going to take them out a few weeks ago. We had the batteries stored in our basement on a shelf. Put them in and went to fire them up. The 2008 fired right up and was ready to go. But the 2007 when putting the key on the DESS post the screen came on for a short period, but there were no beeps at all. Then I tried starting it thinking maybe the beeper wasn’t working. Nothing at all. So I switched the battery out of the one that was working thinking maybe it was just the battery. Again the same exact thing. So it wasn’t the battery. Did some research and wasn’t really a whole lot about the topic on that model year. I found some stuff that suggested that it was possibly the DESS post was bad and I would need a new one. So I wired up the new DESS post. Same exact thing. When the key is put on you can here like a pump is turned on or something and the screen comes on for like 5 seconds and then goes off. Nothing else comes of it. I put my key from the 2008 on it to see what it would do and it has the same result as what happens with the correct key.
Any ideas would be much appreciated thanks!!
That sounds like an ECM problem or some computer has gone bad.
So would the best bet be taking it to a dealership and seeing what computer system has gone bad? Because the computer systems are very expensive? or is there a way to diagnose it by my self.
The best thing you can do is take it to the repair shop and let them hook it up to BUDs to see what is wrong. It could be something simple like a terminal is loose or as bad as the ECM is bad.
I have a 2001 xlt 1200 yamaha waverunner. When i hit the start button it makes a lound horn like sound and i can feel vibration under the black yamaha cover. Any idea what it could be, sounds like starter isn’t engaging but not sure. have a video of it on my phone
That’s a new one, I never heard a jet ski make a horn-like sound. The thing that comes to mind is the starter motor jammed or something in the pump is jammed.
I have a 2008 Kawasaki 15F and my frustration is that when the ski is cold it starts right up, runs a little ruff until it warms up then runs great. When i come back in and try to restart the ski it will not start until it cools down? I have changed the battery, I also change the plugs every year. Last year i even change both coils because i thought maybe they went back. I would appreciate any advise.
I would check the fuel injectors. I had a jet ski that did something very similar to this and it was because of the fuel injectors and bad gas.
Hi Steve, I’ve got a Yamaha vxr 2012. Battery had plenty of charge but when we tried to start it there was a faint electrical buzz but did not try to kick over at all. Tried pressing the start button multiple times but same thing happened. It eventually kicked and started. I switched it off after about 5 minutes out on the water for about 2min then tried starting it again and it wouldn’t start. Took the seat off and wiggles the cords and it eventually started again. It ran fine for another 2hrs then after we got it out of the water to clean it out with fresh water it wouldn’t start again. Checked the battery and it was still fine… is that likely the start relay or another electrical issue?
Sounds like the starter relay.
Hi Steven, we bought a 2005 seadoo Gtx 155 last summer. Had a blast at the lake all year. We got it winterized end of the season, and it’s been stored in the garage. We are taking it back to the lake next week. What do u recommend for maintenance each year? Should I go ahead and get the oil changed and new spark plugs each season before I take it out? And is winterizing at my dealer all I need to do at the end of each summer? Thanks!
What I do is get my jet ski winterized with oil change every year, I only do this because things are cheaper in the winter and I don’t need it then. Then when the season starts I put some fresh gas in the tank and change the spark plugs. If you didn’t have the battery on charge during the winter I charge the battery or get a new one. If you didn’t change the oil in the winter I would go ahead and do it before you ride. An oil change once a year and new spark plugs every year is a must and if it gets below freezing where you live you need to winterize it every year too.
Thank you. They winterized it, but did not change the oil, so I will do that now. Also we are going to get the solar charger you recommended because we did not put it on charge all winter. Hopefully it will not be dead for good. It was a new battery last year. The solar charger u recommend comes with a cigarette lighter plug… I assume u don’t use that? And just hook it up to the battery and hang the solar panel off? Also, heard conflicting things about getting it winterized. We filed the gas tank with new gas BEFORE winterizing it. When I too it to the dealer, he said I SHOULDNT have filled the tank, and instead left it pretty low.. your suggestion? Is my full tank going to need to be siphoned out now? 🙁
You connect the 5-watt solar charger directly to the battery. These solar chargers often come with clips that you connect to the terminals of the battery. Leave the solar panel somewhere that the sun can get to it. If the battery is already dead the solar charger might not charge it up enough, it’s more to maintain the battery. You’ll need to get a 12-volt smart charger rated below 2 amps if the jet ski won’t start or the battery is weak. If the smart charger doesn’t charge the battery then you’ll need a new battery. I leave all my jet skis with 1/4 of gas for the winter, never fill it up and let it sit. Gas goes bad over time. Then when the season starts I fill the tank with fresh gas. If you stored the gas without STA-BIL in the tank the gas might not be good. The high-HP jet skis can get picky about their gas, if it’s slightly bad check engine lights go off. I would have the dealer check the gas and if it need be taken it out.
Thanks for the quick replies! Ok, last questions.. if we store the seadoo in a garage all winter, it wouldn’t get any sun, so how often should we hook it up to the smart charger in the winter, and how long to leave it on each time? When they winterized it, they did put stabil in the gas, so perhaps it will be ok? Would stink to lose a whole tank of gas. And finally, is the starter relay an expensive fix? Ours may be going bad bc we have to push it a few times sometimes for the engine to fully turn over. We have noticed the DEES key has to be put on the post just right also.
In your case, I would take the batteries out of the jet ski and put them somewhere off the ground in your garage. Then a few days before you get you jet skis ready for the season charge the batteries with a smart charger. If you got STA-BIL in the gas when it was winterized you should be fine. Replacing the starter relay can easy on some models and hard on others. From what you describe it sounds like you need a new starter relay. Just make sure the battery is disconnected and out of the jet ski before you replace it. This is for safety and often it’s so much easier to replace the starter relay with the battery out of the way.
Hi Steven, great article! So…. here’s my situation… 1997 Seadoo GTI. Bought it a few weeks ago, all service performed by local mechanic. Local mechanic gave advice to crank it up out of water and warm it up prior to placing it in the water after I called him and advised him it wouldn’t crank in the water. I took his advice and it ran for a while; however, it just completely shut off on me a few times while riding as if I detached the cap key from the Seadoo. I checked the key but it was still attached. I held the start/stop button down for a moment several times without it doing anything and it finally cranked back up and made it back to the dock. Later, I checked to see if the Seadoo would crank while on the trailer and now there is no beep when I place the key on, the gas gauge turns on and the red light turns on quickly and both go off. During that quick moment I am pressing the start/ stop button but there is no clicking or anything in the engine. I checked ALL fuses, I checked the battery voltage and am good on that. I placed a screwdriver across the starter relay solenoid bolts without the key on the Seadoo and it sparked and sounded like it was going to crank. Starter Solenoid relay ? If it is the Starter Solenoid Relay would that also have an affect on the beeper? Thanks for your help!
I’ve seen the start buttons on those models go bad or the key or DESS post. It sounds more like the DESS or Key is bad but a 23-year-old jet ski is bound to have a handful of problems so fixing the start button would be worth it too.
Thanks for your help! I will check it out and keep you updated on our findings.
I read your article it’s great. Thank you for all of your advice here.
I made a post yesterday here; however, I’m not able to see it. That is why I am writing this post for the second time.
I bought the Seadoo Spark 2014 last year around August with a bit broken(cracked) hull that I fixed without any problems.
When I bought the jet ski I tried to turn on the engine; however, I was not able to start the engine and I thought that probably the battery is weak or I need to replace the spark plugs. ( I heard the sound that engine is trying to start)
Now when I have a bit more time I try to turn on the engine; however, I’m not able to and I don’t hear anything except one click.
I replaced the starter relay.
I replaced the starter solenoid
I’ve checked the battery and it is good( I’ve checked the battery for load in Auto Zone)
I’ve checked the starter (It’s working great)
I’ve also checked all of the cables from battery to starter solenoid and from the starter solenoid to the starter.
All of the fuses are good.
When I replaced the spark plugs I noticed that they are rusty, and that rust is on the top of the pistons. I wonder if it is possible that pistons got stuck?
What is your opinion on what can cause that engine this problem?
I didn’t winterize the engine because I have no idea that I should do this. I don’t know if this is important, but I live in a place where winter is warm and I parked Jet Ski in the garage all the time.
Could you please give me any suggestions on what I can check before I will go to the dealer?
A hole in the bottom of the jet ski and rust in the cylinders is not a good thing. It sounds like the Spark sunk and the engine took on water and made it hydrolocked. This is not a good sign, I suggest taking it to the nearest repair shop.
The hull was broken outside the water. The engine is completely clean and looks like new and the hull inside looks like new is very clean. I don’t see any signs of water inside the hull, so I do believe that the damage was done outside the water.
Something is not right as spark plugs should not rust. The person who sold you it could have cleaned it up. Something is not right and will need a repair shop to tear apart the engine to see what is going on.
Thank you very much for your advice
Hey – 2006 STX 15F owner – bought it used and it ran great for 3 hours
3rd trip out it will crank hard but not start
Smart trickle charged the battery and it was at 13v
Check that fuel was geting to the rail
Engine cranks hard but never fires
Try replacing the spark plugs.
Actually tinkered with the fuel rail some more – fuel pump may be bad
Ok, so my 91 Kawasaki TS has a very similar issue! When you go to start it and all it does it click, keep holding the start button. I did this for roughly 10 seconds and when i hit the starter button again, it actually turned the motor over. I know, weird….but try that and let me know how that goes.
Sounds like you need either a new battery or a starter relay. If it’s multiple clicks you need a new battery, one single click then you need a new starter relay.
I have Yamaha Ex model Jetski. It unable to start, so after charging it got dry start. But in water it unable to start again. It happens twice the same. So I changed battery to 12v 18 amh (as 19 amh not available in market). Now engine not starting, only there’s tick sounds. Voltage showing greater than 12. What could be the reason please. Is there anything serious.
Sounds like you need a new battery, the one you have has gone bad. Even if the battery charger says it charges fine it still sounds like you need a new battery.
I have a 2004 Seadoo GTX 155 4tec 160hour.
When the engine is cold starts fine (on the trailer and also in the water).
After riding when the engine is warm it takes a lot of cranking to get it started.
Does my starter stop cranking (slow) after a few seconds (like it’s a feature to save the battery), then I have to press start again and go through this 3-4 times before it fires up. Once it starts it runs fine, and always starts right up when cold. Thank’s! Leslie
This is a super odd one. It’s either fuel or a compression problem. This is one of the times I’ll say you need to take it in so someone can get their hands on it and figure it out. I’ve never run into this problem before.
Have a 2011 yamaha vxr. Started up once (no problem), let it ran for 15 seconds, started up twice (no problem), ran 15 seconds, then 3rd time it clicked and the green security light came on, it didn’t start. I let it rest for 30 minutes and it just the green security light came on.
It’s wanting the code to unlock it or the key fob if you have one. To reset it you’ll need to take it to the dealership.
Hi Steve, i have a 1991 Kawasaki 650TS and am having starting issues. I replaced the battery, starter solenoid and starter with no change!?!?!! When i hit the starter button it cranks super slow for a few seconds then all i hear is the solenoid clicking. I can start it with a battery charger on 10 amps and after its warm it will start back up almost every time!! Also getting over 12.4v when it runs, can you suggest anything else to try?
If you can start it with the extra help of the battery charger then that tells me the battery is not good even if it’s new. The battery charger is supplying enough power to make up for the weak battery and that is why it’s starting. Also, if it’s only at 12.4 volts when running it tells me the rectifier or something in your charging system is not working. It should be hovering higher between 13.5 to 14.5 volts. Also, don’t forget to clean the connecting battery wires as they often develop corrosion over time. When you do get another battery make sure to charge it completely with a smart battery charger.
I’m 16 years old and my grandfather owns a 1999 Seadoo gtx he’s no longer physically able to A) ride and B) work on it. Me just getting my boating license have now decided to turn this into my little project to fix it up, so here’s my problem, I put the key on and only 50% of the time the dash board comes on, and when it does it and I go to start it, it gives a kick and dies out, we tried charging the battery and that didn’t seem help. When we do get it to start it dies when you don’t touch the throttle and you have to take the key out and try again. Do you think I need a new battery? Or could this be something else. Thx in advance
I would start with a new battery first.
I njhave a 2005 GTX DI and it was running great. then my son took it out 15 minutes after I had just gone for a ride and it suddenly quit on him. We can start it but now it dies within 5 seconds in idle and quits immediately when moving the throttle. I replaced the spark plugs and checked all electrical connections but no luck. could it be a fuel pump or filter? looks like a monster job to get t out if it is
Honestly, it could be many things with those DI’s. The DI’s from my experiences always get some type of phantom issue that makes it act odd. The fuel delivery system sounds like your issue and it could be the fuel pump or fuel rails. It’s hard to tell on DI’s but fuel seems to be your issue. It would be best to take it to a repair shop especially one that deals with 2-strokes. Those DI’s are cursed if you ask me.
Thanks. Based upon my experience with solenoids and the few PWC local technicians comments, I did not bypass the solenoid during the initial troubleshooting. No traditional clicking sounds, just the whirring noise noted in the earlier post. The whirring noise happens at the initial safety key is inserted on the dash for three or four seconds and then stops and then happens again when the start button is pushed. Just to be sure I decided nothing hurt through bypassing the solenoid and did so and the jet ski turned over fine – starter appears to be okay with that. Is the solenoid the most likely problem or is it possible that there is an issue with the MPEM? Can the MPEM cause the solenoid not to engage? I’m not getting a clicking sound when depressing the starter, only the whirring sound like a small electric or hydraulic motor spinning. It will do so as long as the starter button is depressed. I’m glad to replace the solenoid, cost is low, but I’m stumped by the whirring sound and wonder if there is a problem ahead of the solenoid. I have been unable to find this specific issue in talking with three technicians and looking at on-line postings. Many refer to the clicking of a solenoid as an indicator (which I don’t have happening) but no one has heard of a whirring sound happening under any condition. Any additional thoughts?
Thanks again for the first response.
That sound was common in some DI models and early 4-tec engines. It’s the fuel pump and other compoents “priming”. Every time you put the key on or press the start button you’ll hear this humming like sound. I would replace the starter solenoid and then go from there. Make sure the battery is not connected when you replace it.
Thanks for your very useful comments on jetski starting. I hop you are able to provide possible direction or confirmation on the issue below.
2000 Seadoo RXDI
1. Won’t start. Battery depleted.
2. New battery installed.
3. With safety key inserted two short beeps occur. Electrical panel displays with status information.
4. The first time inserting the safety key with the new battery the double beeps occurred and then there immediately follow a long beep. This happened twice. I couldn’t find a reason for the long beep of which several are listed (wrong lanyard, defective lanyard, safety lanyard in too long without starting or bad MPEM.
5. An attempt was made a few minutes later and there was no long beep following the initial two short beeps.
6. With the two beeps and no following long beep, the red start button was pushed and there was a humming sound similar to what a spinning electric motor or the sound a small hydraulic motor might make. Nothing else happened. No clicks or other sounds like I am familiar with on automotive units when a solenoid or battery is weak or bad.
7. At the next attempt the humming sounded as soon as the double beep was heard with the insertion of the safety key, but without depressing the start button.
8. The humming sound continued on its own for a few seconds and then stopped.
9. The red start button was pushed and the humming sound initiated again until the red button was released. The start button checked to verify it was not stuck/sticking in a depressed position. It was not.
10. Time was taken again to verify battery electrical connections were tight, which they were.
11. The electrical box opened. What to me seemed a significant amount of water found inside. Water removed and the unit dried out, connections of all location checked and the attempt to start the unit again made with the same result as noted above, i.e. motor hum sounded as soon as the safety key was inserted, then stopped on its own and when the start button pushed the only sound was again the same hum as long as the red button is depressed.
Despite being a 2000 model it has only 107 hours on it.
Bad starter motor? Bendix not engaging? Other things I can check? I am told replacement of the starter motor is difficult and expensive due to time.
Thanks for any thoughts or direction. We don’t have a local dealer or repair so I would appreciate as much direction as possible before traveling to a dealer.
I would start with the starter relay and then the starter motor. The starter motor won’t be easy but nothing is easy on any DI models. The honest truth is that any DI Sea-Doo I’ve run into always had some type of phantom electrical problem. You’ll fix one thing but another electrical problem will show up soon. Hopefully its something simple like the starter relay.
Have 1997 STX1100. When I hit the start button, I can here the starter turning but the engine does not turn over. Replaced battery with new one and a new solenoid. What could be the issue. Thanks Pat
Could be either a bad starter motor or something in the engine is locked up like water in the cylinder.
Hi Steven amazing articles by the way… I have a pair of 2018 season spark trixx. I was wondering if you can give me some tips on how to clean them after riding. As well as tips you think I should know as well.
Here is how I clean jet skis https://www.steveninsales.com/how-to-clean-a-jet-ski-my-way/
And here are some tips https://www.steveninsales.com/jet-ski-beginners-guide-18-things-know/
Hi steve running a 2008 seadoo – ran like dream today for 2hrs then went to restart on the water – nothing no click no thud – new battery 12 months ago and new genuine stater solinnoid- tried other learner key no good – dash instruments come up – but no start click or thud – biggest concern – no likely to get into mech for 2 weeks – so was unable to flush with water on return – salt was very concentrated today – btw disconnected and connected batt – still no good- tony
Could be a bad DESS post or start button.
I have a 2000 GTX that got water in engine compartment and wouldn’t start only clicked so I replaced starter relay and now only partially turns over want stay turning over I have to keep pushing starter over and over and I noticed circuit box and wires get hot and I hear some noise coming from circuit box . Also don’t make beeping noise when you stick key on anymore. Thanks
Sounds like it’s hydro-locked. Avoid trying to start it and get it to a repair shop so they can remove the water from the engine.
Hello I have a seadoo gtx I was running and then stop for a couple of hours after that I try to turn on and just make a click click noise please can you help youwith an advice. Thank you
If it’s one click then its the starter relay, if it’s multiple clicks then its the battery.
2004 SeaDoo GTI has hard time recognizing the key, Sometimes it beeps right away and other times it takes a long time for it to beep so you can start it. Could this be caused by a bad Dess post?
Could be a bad DESS post or a bad key.
I have a 2007 GTX Seadoo and it ran fine last year. When I put the battery back into this year, I had trouble getting the gauges to come up, so I could start it. When you put the safety lanyard on sometimes the gauges came up and it beeped and sometimes they didn’t. When it did start everything seemed to work fine. I was riding it the other day and all the sudden it shut off with no alarms or codes and now it won’t initialize or start at all. Could this be a battery problem?
It could be a bad battery, weak or poor connection, bad electrical component, and many other things. But I would start with the battery first and make sure the connections are properly connecting the battery.
Hi, I’m female and new to jetskiing. I have a 1997 seadoo gti, ran good the first 2 times out, then on the 3rd time, it started to bog down at full throttle . Limped it back to the dock . It shut down so I tried to start it again, and now it just makes a loud click (clunk) sound and won’t turn over . Battery is charged, but it only clunks once and does nothing. I’m not sure what happened.
Usually, when you hear one clunk it’s a bad starter relay. As for the bogging down, it will be a different story and a lot of things could be it.
Hello Steven, kind of you to answer all of these questions.
2006 Kawasaki STX-12F
I went for a ride yesterday and everything was fine. After the ride tried to install a battery tender adapter to the battery that would click-in as opposed to attaching with two clamps. I was having an issue getting the right angle with the screw driver I was using and gave up.
Today I try and start it won’t. maybe I need to ensure the termindal block tightly screwed in?
I took a video with sound to show my attempt to start it.
Heres the YouTube link:
Usually, multiple clicks is a weak battery or a loose battery connection.
I’ve just solved my mystery. Blown fuse.
I have a Yamaha FXSHO and was out this morning cruising at about 60kph and suddenly no power (electrical). Motor stopped immediately and no power to anything. Completely dead. Brand new battery and showing good voltage. Any ideas?
Riding my 04 season yestadAy it just stopped and now won’t start it clicks once but wont start and key comes up on the dash
Sounds like you sucked something up. Usually when you’re moving along and the jet ski shuts off something got sucked into the intake. You might not have heard or felt it but it does happen. The click would be because whatever is in there is keeping the engine from spinning over because jet skis use a direct drive anything that blocks the impeller also blocks the engine from spinning.
I have seafood 2015 jet ski. Yesterday I started after 4 months it did start and I went in water it stopped I try to start it is clicking but not starting on display it says BR. Please help me out
I would start with replacing the battery. I’ve seen a weak battery throw up iBR faults on the gauge.
Hi, Seadoo gsx starting problem.When i press start button the engine makes half a turn and stops. It does it several times in a row. Starter solenoid is new, battery is good, cleaned grounds. I put a test light on the yellow/red wire from the ecu to starter solenoid and if i press start button the light comes on, but when engine makes half a turn only the light only makes a flash as long as the time engine makes half a turn. Is it possible to have a problem in ecu or what can it be? If i get the engine running it will start better, almost every time i press start, but still makes half a turn starts occasionally. It is like starter solenoid will loose signal from ecu and then stops.
It might be a bad starter motor.
ive had my 2004 seadoo sit all winter in the shed and getting ready for the warm weather battery was disconnected the whole time I’ve connected it but it was flat so I charged it over night while the terminals where off as you should hooked the terminals on after being charged and started up had it running for approx 5mins on the Trailor with water then turned it off since then it won’t start again just making a clicking noise can a starter relay fail that quick also the button on the handle bars doesn’t Spring out the best can that cause a issue
Yes, the starter relay can fail out of nowhere especially if it’s the old brown style one. The black Sea-Doo starter relay will be the better one to get. But you said you had it running on the hose and if you didn’t follow the correct procedure of turning the water off before turning the engine off you could have hydro-locked the engine and that would make it click. If that is the case avoid starting as you could do damage. You can buy a new starter button just about anywhere, they just pop out.
I have a 95 Sea-Doo GTX. I’m sure the starter relay is going because I have trouble starting it but also I think there’s some sort of fuel issue because when I try to start it, if I try to start it, it will chug and then I will pull the throttle open all the way and then it will start. Today it actually died spontaneously in the water twice. I have a guess that it has to do with the fuel issue or a carburetor issue. Any thoughts?
Sounds like carburetor to me, but it could be many things and it’s best to let a repair shop look at it hands on to see what the problem is.
Hey Steven, we have a 2005 Seedoo GTX that is giving us starting fits this summer. It starts intermittently and has a new battery. One time it will start, the next time it won’t. We’ve had it into the shop twice and they can’t replicate the problem. Starts right up for them every time. It almost seems like it could be a loose wire somewhere. Are there wires in the steering assembly at the start/stop switch that could be loose? Called the shop again today and they think it might be the starting post. What’s your opinion. I’m not a mechanic and can’t find any you tube videos on any starter problems with the key post or start/stop switch. Ideas?
I would have them clean all the grounds to perfection and the connectors that go to the battery. I’ve seen dirty grounds cause odd problems. They really need to clean them, there is like 3 on the front of the engine that should be cleaned well. I’ve also seen fuel rail or injectors go bad and cause a jet ski that will start sometimes but not the other time. It was like a leaking fuel injector that flooded the engine but it would still spin over but never start. There are many options to go from and the dealership should be able to figure it out or use their chat with Sea-Doo to figure it out.
Hey man. I have 2 95 seadoo Xp’s I’m having trouble with. Yesterday they were running fine when my buddies took them a little shallow and sucked rocks into both of them. I took apart the jet and had to replace the wear rings. Easy enough. But now both won’t start. They have new batteries that are holding charge and I suspect the solenoid so I ordered new ones. I tried jumping the solenoid with a screwdriver. It turns over that way but won’t start. Both don’t respond at all when I put in the key and push the start button. No click or anything. Any ideas??
Could be a bad key switch.
I got a tiger shark tsl 900 I have 2 problems 1 st is hard starting turns over good but takes a bit to start 2 no is when you do finally get it running you have to hold the gas down and it hesitates then just goes full bore only you basically get idle or super fast any help would be great
Sounds like a clogged carb, but it can be many things as those Tiger Sharks are a handful.
Hey Steven I have a seadoo spark that was not starting or gauges turning on at all so I replaced the battery because the other one tested bad and now that it has the new battery in, still nothing turns on as though there is no battery at all
It’s best to take it to a dealer, some models sparks had a wiring issue where it would rub. It could also be a bad kill switch or even a blown fuse. Also, don’t forget to make sure the battery is connected the right direction – I’ve done this before and can blow a fuse.
Hi. I have a 2007 kawaski stx15f. New battery from Walmart. This is the 2nd one in 1 month. No lights on panel. No clicking. I even tried to jump the starter solenoid with nothing. What is my next move.
It could be a bad kill switch or blown fuse, it’s best to take it to a repair shop let them see what is going on with it. Too many possibilities and a repair shop might be the best way to go with electrical issues.
Hey Steve just a quick question , I have a 1994 Polaris Sl 900, It has been sitting for about 3yrs and has not been started since then. It worked just fine before but I recently tried to start it ,but will not turn over , I tried turning the shaft by hand but it seems like the motor is locked, could this happen? or maybe battery ?
Yea, if the engine sits for years and was not fogged then rust can form and lock the engine. It’s best to do storage procedure before storing a jet ski for a long time. To get it fix might require a teardown, but I would drop it off at a local repair shop to see what they say.
hey i have a 1997 kawasaki 750 zxi i know the battery is bad but i got this jet ski from a family member that could not get it to run and i dont want to sink a lot of money in it so what im asking will it get enough power thru jumping it off with my truck to make it start it cranks great but no fire to plugs no lights on the panel btu the fuel gauge works and it has plenty of oil i just want to hear it start before i replace the battery
Never jump a jet ski battery with a car or truck, you’ll fry the electronics. The only options you have is let the battery try to charge or buy a new battery. It’s best to let a repair shop look at it since you may have electrical issues if no lights come on.
1999 yamaha 3 cylinder charged for couple hours and go to start I get the word start on dash and it makes a weird buzzing noise when I hit start. Battery bad? Please help thanks
Buzzing could be a messed up relay, either starter or a smaller one in the electronics box. It’s best to let a repair shop look at it.
I have a 1998 seadoo gts jet ski. It will not start. I replaced the battery due to it being junk. Then replaced spark plugs. Still would not start but would crank. If you put starting fluid or gas in carb it will run. So I blew threw all glass lines and vacuum hoses. And checked all hoses for leaks. I Found no file going to carb due to lack of vacuum. So I rebuilt the carb. And it ran for about 30 seconds then stopped. So I tried to start it again with starting fluid and it started up but died any ideas?
Try replacing the fuel lines and fuel selector.
Hi Steve. I have 2003 sea doo 4 Tec. Got it used. The guy I bought it from said the starter relay was going bad, so I changed it. It ran great all morning, then after sitting on the beach for a couple of hours, I turned the battery on to go home and it tried to start itself. After wiggling the wires around, it started normally. Then when i started going and bouncing, it would cut out again. After about 10 min of idling, I had to get back to the dock, it ran perfectly again. I cannot find any loose wires. Have you ever seen this?
You said you turn the battery on, this must mean you have a battery switch. Jet skis don’t come with battery switches and it’s not the best to have them because they create an unneeded load between the battery and the starter. This could be your issue as you have too much going on between the battery – starter relay – start motor because of a battery switch. But if someone put a battery switch on a jet ski then it must mean it was draining the battery and you could have an ECM problem. Don’t forget to check the obvious stuff like the battery’s condition and if the connections are tight. If anything it would be best to let a dealership look at it.
Hello Steve. My daughter and her boyfriend were riding my 2016 Yamaha V1 sport this past weekend. The ski was running great when all the sudden it beeped 4 times, the warning light came on, then it went completely dead. I had to tow them in with my pontoon. I took the ski out of the water and it will not do anything. The gauges do not light up and it doesn’t click when you turn it over. I charged the battery but it still doesn’t do a thing. Got any idea what would make a jet ski completely shut down. It’s a 4 stroke with 12 hours on it. Any help would be appreciated.
That is very odd. Since it so new I would take to the dealership and see what is going before messing with it just in case it’s a warranty item. The only thing I would maybe check is to see if the battery connections are tight. I’ve seen loose battery terminals stop a jet ski and throw odd codes before.
Any idea where the rectifier is located and the best test method in checking it? There are any marine shops near me or I would take it in for diagnosis. Thank you again!
The easiest way to test if the rectifier is bad is with a volt meter. I don’t recommend doing this unless you have some experience with a volt meter and working on engines before. With the jet ski out of the water turn it on and measure the voltage of the battery while it runs. After firing up the battery should be charging around 14 volts. If the battery is at 12 volts or lower then this tells us something is wrong the charging system, it could be rectifier or stator or wiring or electronics. Remember you can only run the jet ski out of the water for about 30 seconds.
I have a 1996 Tiger Shark 900 Monte Carlo that hasn’t been started in several years. With a hot battery it will not crank over at all. Only makes one single click. Changed starter solenoid and got the same results. The engine rolls over when I turn the drive shaft so it is not seized. Could it be the starter relay and if so where is it located? Any help would be greatly appreciated.
It’s not often that someone talks about a Tiger Shark. I think it might be your starter motor that is bad if the engine moves freely, the clicking could be the starter motor just giving up. Make sure the wiring going to the starter motor is good and tight and not corroded, the jet ski is 21 years old so there could be other issues too.
Thanks for all the time you put into helping others. This thread is great. Bought a pair of 2013 Kawasaki STX-15Fs last summer. Love them, BUT, one keeps losing charge. Replaced the mis-sized small battery with correct size and it made it 3 weekends, but now, when I go to start, I get one click, then several smaller ‘clicks, but nothing else. Display does not show the battery low, as in previous instances. 3rd time with this happening, and on the first two, I towed back to trailer with 2nd ski and got water in motor(question/topic for a different day). Any ideas? Starter Relay? Rectifier? Other? Thanks again!!!
This is a tough one, I recommend letting a dealership look at it. But if I had to guess I would say the rectifier is bad and draining the battery when it runs?
Thanks for the help. Appreciate it.
Have a 2011 gti. When you turn off engine something keeps running. Sometimes when you attach the key and start then turn off it quits. Other times need to disconnect the battery. Sometimes it won’t start at all and you have to disconnect and reconnect the battery then it will start.
That is odd, never heard of this one. It would be best to take it to the dealership and let them look at it. I can only guess that maybe it’s the fuel pump still running which is not good at all.
Hello sir, from reading you page and your replies i’m certain all i need is a starter relay, however i figured i’d still ask. Last week ski would try to start over, sounded like starter was hitting, PTO would rock back and forth, charged the battery a bit and she fired right of. This week launched the ski and went to start, nothing, not a sound, not a click, nadda. Brought it home boosted battery, now when i plug the safety switch in, i can hear the fuel pump prime, but when i press start, she gives me one solid hard click from the relay. Then she’ll do it again and again all while depressing the start button. But she will not fire off. Before reading this i was preparing myself for a starter replacement. Thoughts?
I would start with the starter relay first and then replace the battery. If that doesn’t fix it then you need to take it to a repair shop to let them look at it.
Steve, i have 2004 SeaDoo RXP. These past two days, it starts, runs great for about 90 minutes or so then dies, like you pulled the lanyard. There are no beeps that would indicate the key is in place.. try and try and try no power. I tow it back in, get it back home an hour or two later, put the key on and she will start like nothing happened… This has happened back to back days. Any suggestions.
It would be best to take it to a dealership to let them look at it. Sounds like a bad key or DESS post or ECM but it could also be many things.
I have a 1996 seadoo gti new motor ,new battery ,new starter relay . Press start buttons gauge lights up the four red lights come on for the battery ,temp,gas and oil then go off no beep .low gas stays on I have 2 gallons in the machine . Plug my dess key in still no beeps seadoo won’t start ?
Your ski has a lot going on. To be fair it is over 20 years old and things not working will be common. So many things to try, but maybe it’s the DESS post that is bad? Just hard to tell on a ski this old, it would be best to take it to a shop that still works on 2 strokes.
I have 2015 GTX is limited 260 and when I push starter button nothing happens. Dash won’t light up. When u attach key… same thing. Battery has been tested and shows it’s ok.
I would try a new battery, I’ve had batteries “test fine” but actually was bad. On that model, you should be able to press the start button first and the gauges power up and then put the key on. If that doesn’t happen and you put a new battery in it then the next step is to take it to the shop. I would take it to the shop anyways, the battery in that model is hard to get out.
Hi Steve I have a seadoo gtx 4-tec that won’t start properly it turns over and try’s to fire revs to about 350rpm but then cuts off. Reading all your other comments sounds to me like it could be the starter relay just wondering if you had any other thoughts? Many thanks great site
If it’s turning over then it’s not the starter relay. The way you tell if it’s a bad starter relay is if it doesn’t turn over at all or just make one click. If it’s turning over then it would either be a bad battery or starter motor. It could be even a bad ECM not telling it to fire off. The best thing to do is take it to a repair shop and let them look at it.
I have an rxt xrs 2014 Yesterday he first started beeping and it says low voltage it ran 3 or 4times after that and now he wont start the engine Light is on when i hit the start button it jus makes 2 clicks and wont start? I would apricate any help
Probably a bad battery. It would be best to take it to a repair shop to have them look at it.
I have a 2008 STX 15f. I replaced the battery so it’s not a battery issue. When I click the green start button, I hear a click but the starter doesn’t turn the engine over. I tried jumping the 2 terminals with large red wires at the rear of the ski – is that the starter relay or something. Anyway doing that didn’t do anything. It didn’t even make the click like you do when you press the green button. Any ideas? Thanks!
Yes, those two big terminals with red wires is the high power side of the starter relay, avoid jumping those two points as its dangerous. Even if it’s a new battery I would still check that by taking it to an auto parts store and let them do a load test on it. I’ve seen new batteries go bad out of the box before. If that’s not it then it’s either the starter motor or something keeping the engine from spinning over like it’s hydro-lock, blown, or something is in the pump. It would be best to take it to a repair shop to have them look at it.
Hey steve i just bought a 2010 yamaha wave runner vx110 and i changed the oil and spark plugs and i ran water through it using a hose, while it was running i kept reving it and after 5 min of doing that white smoke came from the back than i cut it off and when i tried to start it, it wouldnt evn turn and i doubt its the battery because i was using a booster box to jump them. Any thoughts of what the problem could be?
From you saying you ran it on the hose makes me think you hydro-locked it. There are special procedures to follow when running a jet ski on a hose that you must follow or the engine get’s hydro-locked. It’s best to take it to a dealer or a repair shop to have them look at it.
Hi!! I have a Polaris JetSki We just replaced the battery.. and when we go to start it it sounds like it wants to start but won’t.. but when we hook it up to a battery charger it starts right up and will run until we shut it down.. then we have to repeat with the battery charger…any ideas?
Could have gotten a dud battery. Get the battery load tested at a local battery store or a place like Autozone.
Hi Steve, 2007 Kawasaki Ultra LX starts fine with new battery. Then last couple times BAT shows up and beeps for few seconds on start up. Took battery home and fully charged after checking it with a voltage meter. Anything else we should check. Thanks
Never trust a battery charger or a volt meter to determine if a battery is good or bad. A battery charger or volt meter goes off how much voltage the battery has, but it’s not voltage that starts a motor but amps. To measure amps you’ll need a load tester. But you might not have a battery problem but a rectifier problem. It’s best to have a local shop look at it.
Steve, Thanks for the info on battery. Did a load test and it is still good but not as good as it can be. Within the low normal range.
That being said…can a battery with low amps cause the jet ski to run only at 3000 rpm and then all of a sudden run normal after battery charges up when running?
When jet ski first starts up we get that low bat warning and flashing light. You can only then throttle to 3000 rpm or so. Basically about 5-7 MPH. Then after about a minute or so the ski then runs normal and then accelerates.
Could that be bad battery causing the ski to protect itself with the warning light on battery and the self charges in water.
Thanks for your time. John
Could be a bad battery or maybe even a bad or going bad rectifier. The best thing to do is let a shop look at it.
First, great site with a lot of great information.
I have a 2003 Yamaha waverunner xl1200 that I pulled out from winterizing. Put charged battery in, cleaned everything up and tried to fire it up. I get a few sounds from it.
I get an attempted turning over, kind of like a swooshing sound and then some clicks/grinds.
Was thinking of replacing the starter relay. I changed the spark plugs just to rule that out.
Sounds like a weak battery. If you’re getting some turnover and many clicks that would mean the battery does not have enough power to start it. Even if your battery charger says its charged it could be lying to you. Either that or you have something blocking the engine from moving or a bad starter motor. I would do the battery first.
Bought new battery, charged it up overnight. Just installed it and fired right up.
This is my first year winterizing. I used the hose adapter and when starting noticed a lot of exhaust smoke (blue). Is that normal and should I be worried?
Was going to go drop it in the water and run it at the launch to test things before taking family out.
Glad it worked out. Looking at your past comments it looks like you have a 2-stroke jet ski. It’s going to be normal to see some blue smoke, more if it’s out of the water and even more if you haven’t fired it up in a long time. Since you said it was winterized and you just started it up I would go ahead and replace the spark plugs since most people fog the engine when they winterize them and that can foul the plugs.
Thanks again. Ran like a champ! Since I was having issues starting for the first time I took the time to replace plugs right along with battery.
Thanks for all the advice and guidance.
Steve, you describe it as a single thud, I hear it as a “chug.” Are we talking about the same thing?
Probably talking about the same thing. If you’re hearing one single noise when you press the start button then it’s probably the starter relay. If you hear multiple noises fast then it’s probably a weak battery.
HI Steve just bought a 2012 rxpx 260 with only 30 hours on it. Machine is like new. When I try to start gauges turn on but that’s about it.. no warning lights or anything would this be week battery or starter relay?
Sounds like a weak battery. A 2012 RXP-X would use an ETX30L style battery.
Hey Steve thank you for the info. Those are some good possibilities. It could definitely have been something with the carbs. I know that the ski sat for a couple of years before I got it because of a bad wear ring. After draining the old fuel, replacing the wear ring and firing it up it ran great so surprisingly it didn’t need a carb rebuild. Its been a while since then and it has been running great but who knows the carbs could have definitely gotten clogged for a little because they have not been rebuilt in quite some time.
There could also be a good chance there was some water in the electrical. My brother did say that the ski hit a wave right before it shut off. Or maybe the harness for the start/stop switch has some corrosion. If the ski shuts off again I will take a look at the wiring and see what kind of shape it is in
Hi Steve I have a 1995 Yamaha Wave Raider 700. It runs like new, has a dual carb setup which is in great shape, and has never left anyone stranded on the water until recently. I have trusted the ski enough to ride out miles from the dock. While riding the other day, the ski shut off and after that would crank but would not start.
We were lucky to have someone nearby tow it back to the dock. Once we had it back at the dock it started up just fine. I took it out on the water and had it at wide open throttle and it ran great. We had no more issues that day. I don’t believe its a problem with the battery because no connections are loose, and the ski does not overheat at all. Runs on 50-1 premix and the plugs were changed a month ago. I don’t think anything was stuck in the pump either. I’m puzzled as to why it would shut off like that and then run perfectly fine a half hour later. Was hoping you might have an idea of what was going on with it. Thank you for the help
It’s hard to pinpoint anything since there are so many options. Could be old fuel line, bad gas, on/off fuel switch going bad, carb got clogged for a bit, water in the electrical for a bit, kill switch going bad, etc. Best thing to do is have a shop look at it. It’s going to be normal for a ski as old as yours (22 years-old) to have odd things to happen to it.
My 2004 gtx supercharged don’t start but before this happens i need to press multiples time the start/stop button to finally start.Now don’t star when i put the lanyard a long beep coming up and the cluster just said the sea doo word and i check the code is p1682.The code means ems comunication error.I change the ems 2 weeks ago.I think maybe is the battery dead or the starter relay because before this happens i press the button more than 3 time to finally start the jet ski.Any suggestions?
Pressing the start/stop button multiple times before it would start is a sign of a bad starter relay. The only way to solve the communication error is to take it to a dealer as it sounds like when you got the ECM replaced you didn’t get it matched to the gauge and as a security measure, it’s not communicating. No way around this take it to the dealer.
I have a 2011 wave runner vxr started fine at first parked it then went to ride again and won’t crank. Will crank with battery charge as soon as charger is removed it idles weird and starts beeping showing engine on display have a new battery I put acid in now waiting for a full charge just wasn’t sure if it’s the battery or not..
Sounds like a battery. If I were you I would stick to seal batteries as the ones you fill can’t always take the abuse of the waves that a jet ski goes through. I talk more about batteries here.
Ran a 2005 GTI, fresh off the sales floor last summer (2016 n bought used). Was dumb enough to pull into a shallow water boat ramp n suck up gravel. Changed the ware ring and installed a New stainless impeller. Put New battery in it, conventional gas, etc.
Now engine only bumps when hitting start button. Battery check at Advance auto, new and good.
2005 GTI would be a 2-stroke and 2-strokes have a thinner drive shaft that can bend easily if you suck something up. Would be best to have a shop look at it.
Shafts straight. Checked it all out when I installed the new ware ring and impeller. The engine does a ooh-ahh (for lack of a better sound spelling) when the start buttons hit. Like its getting only a 1\16 of a full rotation then dies until start buttons hit again. No continuous cranking to start
I’m starting to suspect the batteries my wife bought. Although these batteries cranked all our PWC’s when new last summer, they did go low over the winter due to not trickle charging. They are Wal Mart brand Everstart Premium Powersprots series (or something like that) and I’m thinking that the auto shop, due to not testing under load, recharged them, did the test, and stamped them good. They don’t seem to have a CCA or CA label on them which is suspect also. I’m pretty sure this ski needs 270 CA to crank reliably.
Whats you input on these batteries wife put in them ?
Be careful with drive shafts as they can “look” straight. It’s best to roll them on a flat surface. You never mentioned checking the starter relay which is easy to replace on that model. I would see about replacing that or checking to see if power is leaving it and going to the starter. I wouldn’t trust those cheap batteries either, I’ve had a number of those seem fine and charge fine but really was dead. Always buy a good sealed battery for jet skis, they cost more but hold up way better. If the battery is good and power is going to the starter then it could the starter that is worn out or has broken/jammed Bendix. Or you sucked up something that broke something on the inside of the engine past the drive shaft. I would start with the starter relay, if it’s brown then it definitely needs to be replaced, if its black then might still be bad.
Hi! I have a rxt x as rs 2011. Old battery got the panels starting but battery was to old so I replaced it with a new. Battery charger shows battery is full but my Sea Doo is completely dead with the new battery. Any ideas please?
Never trust a battery charger to tell you if a battery is good. A battery needs to be load tested to see if it’s any good as battery chargers can sometimes lie to you. I’ve seen new batteries dead and not able to take a charge so I would see about getting it load tested or get another one first.
2009 Yamaha FX Cruiser SHO. Battery tested good, replaced the starter relay and still get a single click that seems to be coming from behind the fuse box which is where the starter relay is. Is there anything else that could cause a single click when attempting to start this ski. Any assistance would be greatly appreciated.
It could be many things, from the starter, a low voltage relay, too many other factors. It’s best to have your local dealer look at it. You could also check out the green hulk forum here as they deal with jet ski’s and someone might know the exact answer.
Do you even get a click? My 2009 VX Cruiser alarm computer is not responding to the fobs. The alarm beep does not sound and if I hit the start I get action on the display but nothing else. Took it in to be reprogrammed, computer can’t connect to the reprogramming key. T.B.C.
2013 Gtx 215 won’t start. Replaced battery, hit start button, can hear the solonoid engage but it gets a half a crank.
If it’s a new battery and you get one solid click from the starter relay then the starter relay is bad. If you get multiple clicking then the battery is weak. Always be careful when dealing with HIGH CURRENT items like a battery and the starting system. When in doubt visit your local shop.
Would the starter going out cause it to lose power and just completely shut down
No, but if you’re hitting the start button and it sounds like something is moving but the engine is not turning over then it’s a good chance it’s the starter motor. It’s impossible to fully diagnose anything over the internet and the best option is to take it to your local repair shop to see what they say.
Hi Steven I have a Yamaha gp 1200r I just bought 2000 model I rode it the other day maybe a mile and put it back on the trailer just wanted to make sure it ran before I bought it today I ran it and it did not have near the power as it did the other day and now it won’t crank I got the starter button and it clicks then sounds like a wheel is turning or something but the motor is not turning over battery checks out good with my meter!
It sounds like the starter went out. It would be best to have your local repair shop confirm this.
i have 2006 seadoo gtx , It turns over but wont fire up, the sparks and coils in good condition, i changed the injectors, fuel pump and TPS sensor and still have the same problem no fuel spray out from the injectors, the voltage coming to the injectors is 10v , what could be cause this issue ?
It’s hard to say, the best bet is to take it to your dealer and let them hook it up to the computer to see the fault codes. If I had to guess it sounds like the ECM is not sending the signal correctly to the injectors. This may sound silly but make sure to have fresh gas in the tank. It’s easy to overlook the simple things (like gas) that could be causing the problem. But above all else, something like this needs to be taken to a dealership to see the fault codes.
It has a brand new battery that I put in so possibly it’s the starter relay. Thanks for the support!
I have a 1996 Kawasaki 750 ss. I recently have taken it out 3 times and randomly when i am on the water and want to start the ski back up it would not start or make any noise. This only happens on the water. When Im on the trailer it always starts up. It will start back up on the water eventually when it wants to but I find that strange. Just bought it a month ago and looks clean and rides great! Got any ideas on what could be causing this? Possible starter relay or maybe even the spark plugs? Thanks
It could be many things and it would be best to take it to repair shop. If the ski starts on land but not on water it is usually the battery do the extra power needed to start on water. It sounds like your problem is deeper than that. It could be the angle the ski is on when on the trailer compared to the water that allows it to start. It’s so hard to tell and it would best to take it to a repair shop. I would start with the battery and the starter relay first to see if that fixes the issue.
Have two identical a 2011 Gtx seado won’t start, display comes on but nothing happens,says it’s reading keys, have about 7 hours on both kinda funny both acting the same
Most likely a dead battery. If both of them have very similar hours then they both get used the same and if they still have the original battery in them then its time for new ones. 7 hour is quite low for a watercraft that is 6 years old, riding them more often will help keep the battery charged. Or you can use a Solar panel to keep the battery charged when you’re not riding them. Also, those year models did have issues with reading the key, you need to take it to your local dealer so they can update the software and the DESS post so it can recognize the keys better.
Our seadoo GTX is not starting through the starting button, but if manual start (we put jumper wire to the starter relay) is done the unit is working. What could be the possible problem
Sounds like you need a new starter relay.
Did you ever figure out what the problem was. I’m having the same problem on a 2008 Yamaha 1100 ski. Battery is new starter silo ode is good also changes stArter button. Russ
Hi mate i got a seadoo gti130 2012
Iv been riding it for past 4 days about 3 hours a day, yesterday i went to start it and just kepted sounding like it wanted to start but it wouldnt fire up, i tried 3 times then it started, i rode for about 10 mins turned off and then it wouldnt start
Pushed jetski along beach to trailer
Any chance you would no what it would be mate? Starter motor, battery, spark plugs? Jetski just hit 30hours
If you tried 3 times to start it then it’s a good chance it’s the starter relay. If the starter relay doesn’t fix it then it would need a new battery. It’s very rare that it would be the starter motor. If it was the spark plugs then it would run rough, but it never hurts to replace the spark plugs. I like replacing my spark plugs every year but I doubt that is your problem.